can mq2 gas sensor youtube

LPG Gas Leakage Detector Using Node MCU With Blynk ...

Here we use an MQ-2 gas sensor that detects the LPG, Alcohol, Smoke, etc, gases. If there is a gas in the air the resistance between two electrodes of the gas sensor gets increased according to the gas presence. We use node MCU as a microcontroller or a wifi development board that reads the analog values from the gas sensor. In the code, we set the gas value [200]. The node MCU sends these ...

Get Price

Chat With WhatsApp

Smoke Detector System Using MQ2 Gas Sensor and Arduino

· The MQ2 is one type of gas sensor, which can sense Smoke as well as LPG, Alcohol, and Methane. Arduino board is the main brain of this system that controls the whole system. The MQ2 sensor continuously measures Smoke level in the air and sends data to the Arduino board. Then Arduino prints the Smoke level value on the OLED display in the PPM unit. The LEDs and Buzzer used as …

Get Price

Chat With WhatsApp

MQ-9 gas sensor - Arduino Learning

· MQ-9 gas sensor has high sensitity to Carbon Monoxide, Methane and LPG. The sensor could be used to detect different gases contains CO and combustible gases, it is with low cost and suitable for different application. The sensitivity of the sensor can …

Get Price

Chat With WhatsApp

Interfacing MQ-2 Gas Sensor with evive - STEMpedia

The MQ2 Gas sensor has a built-in variable resistor that changes its value according to the concentration of gas. If the concentration is High, the resistance decreases, if the concentration is low, the resistance increases. Besides the built-in resistor, it is necessary to include load resistor, Load resistor serve to adjust sensor sensitivity and accuracy, it’s value can range from 2k ohm ...

Get Price

Chat With WhatsApp

How to Use a Gas Sensor (MQ-2) -

· The Gas Sensor is a sensor which detects gas and smoke with concentration between 300ppm and 10000ppm. He can detect butane, propane, methane, alcohol, hydrogen and smoke. He can be only used Inside, at ambient temperature. He has 2 pins for the power, 1 pin for the analogic value and 1 pin for the digital value. For this project, we'll use the ...

Get Price

Chat With WhatsApp

How MQ2 Gas/Smoke Sensor Works? & Interface it with ...

· Using a simple voltage divider network, concentrations of gas can be detected. MQ2 Gas sensor works on 5V DC and draws around 800mW. It can detect LPG, Smoke, Alcohol, Propane, Hydrogen, Methane and Carbon Monoxide concentrations anywhere from 200 to 10000ppm. Here are the complete specifications . Operating voltage: 5V: Load resistance: 20 KΩ: Heater resistance: 33Ω ± …

Get Price

Chat With WhatsApp

MQ-2 Gassensor |

MQ-2 Gas-Sensor als anschlussfertiges Modul für Arduino und Raspberry Pi. Einfach zu nutzender Sensor zum Messen der Konzentration von LPG, i-Butan, Propan, Methan, Alkohol, Wasserstoff und Rauch in der Luft . Der MQ-2 misst eine Gaskonzentration von 100 bis 10000ppm und ist ideal zum Erkennen eines Gaslecks, als Gas-Alarm oder für sonstige Robotik- und Microcontroller-Projekte. Die Sensoren ...

Get Price

Chat With WhatsApp

How Does MQ 2 Sensor Work?

Also know, what is mq2? MQ2 gas sensor is an electronic sensor used for sensing the concentration of gases in the air such as LPG, propane, methane, hydrogen, alcohol, smoke and carbon monoxide. MQ2 gas sensor is also known as chemiresistor. This sensor works on 5V DC voltage. It can detect gases in the concentration of range 200 to 10000ppm.

Get Price

Chat With WhatsApp

How to Build a MQ-2 Smoke Sensor Circuit with a Raspberry Pi

The gas sensor needs about 5 volts of power in order to operate. This is done by connecting 5 volts to Vcc and GND. The Output pin gives out the voltage reading, which is proportional to the amount of smoke that the sensor is exposed to. Again, a high voltage output means the sensor is exposed to a lot of smoke. A low or 0 voltage output means the sensor is exposed to either little or no smoke ...

Get Price

Chat With WhatsApp

MQ2 Gas Sensor - Working Principle & Its Applications

MQ2 gas sensor is an electronic sensor used for sensing the concentration of gases in the air such as LPG, propane, methane, hydrogen, alcohol, smoke and carbon monoxide. MQ2 gas sensor is also known as chemiresistor. It contains a sensing material whose resistance changes when it comes in contact with the gas. This change in the value of resistance is used for the detection of gas. MQ2 Gas ...

Get Price

Chat With WhatsApp

Professional gas sensing solution supplier with over 30-year gas sensor manufacturing experience Contact Us